c45 steel steel Related introduction

  1. C45 Medium Carbon Steel grade - materialgrades.com

    Jul 19, 2018 · What is C45 Material? C45 grade steel is defined as a medium carbon steel offering tensile strengths in the modest range. The material can be maneuvered with hardening by means of quenching and tempering on focused and restricted areas. C45 can also be instigated with induction hardening up to the hardness level of HRC 55. This grade is in majority situations delivered in an

  2. EN 1.0503 Material C45 Steel Equivalent, Properties ...

    EN 1.0503 Material C45 Steel. EN 10083-2 C45 steel (EN 1.0503) is a high strength medium carbon quality steel. Due to poor hardenability, C45 material is generally used in a normalized condition, and when the mechanical properties are required to be high,

  3. C45 Medium Carbon Steel, Hillfoot

    C45 grade steel is a medium carbon steel offering moderate tensile strengths. The material is capable of through hardening by quenching and tempering on limited sections but can also be flame or induction hardened to Hrc 55.

  4. What is 1045 / S45C / C45 Steel Properties Chemical ...

    C45 Steel Application. 1045 steel is widely used for the industry application that required higher strength and wear resistance than low-carbon steel. And the typical applications are gears, shafts, rolls, crankshafts, sockets, bolts and etc.

  5. C45 steel

    Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. C45 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join Supplier: [email protected]

  6. C45 Round Bar, AISI 1045, DIN 1.1191 - Otai Special Steel

    Steel C45 Round Bar is an unalloyed medium carbon steel, which is also a general carbon engineering steel. C45 is a medium strength steel with good machinability and excellent tensile properties. C45 round steel is generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 700 Mpa and Brinell hardness range 170 210 c45 steel steel

  7. C45 Steel - DIN 17200 - EN 10083 Standard quenched and ...

    C45 steel DIN 17200 EN 10083 Standard quenched and tempered structural steel. C45 steel bar stockholders and suppliers from china. OTAI SPECIAL STEEL Supply in steel round bar, plate, sheet, square bar, flat bar, pipe since 1999.our steel stock more 1000tons

  8. C45 steel

    Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. C45 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join Supplier: [email protected]

  9. C45 Carbon Steel - Delivered Nationwide by West Yorkshire ...

    West Yorkshire Steel are steel stockholders and suppliers of C45 carbon steel round, square and flat bar. Bars can be sawn to your required length in 1 off or multiple cut pieces. West Yorkshire Steel supply flame cut steel profiles in grade C45, which can be surface ground if required.

  10. C45 - BEBON steel - C45 steel plate

    C45 steel plate, EN 10083 C45 steel plate, under EN 10083 standard, we can regard C45 steel plate as high carbon steel.. C45 steel plate is one mainly of high carbon steel,EN 10083 C45 steel plate is for quenching and tempering. Technical delivery conditions for non alloy steels,these steels are for general engineering purposes

  11. C45 Carbon Steel Plates - ganpatind.com

    High Carbon Steel C45 S45C 1045 C-45 Sheets, C45 Boiler Plates, C45 Shim Sheets, C45 Carbon Steel Circle, C45 Cold Rolled Plates, C45 Coils, C45 Carbon Steel Plates Dealer in India. Ganpat Industrial Corporation is a recognized trader, dealer and stockist of C45 CS Sheets Plates , which is also used in domestic, professional or industrial areas.

  12. C45E / 1.1191 - European Steel and Alloy Grades / Numbers

    Properties of steel C45E (1.1191) Weldability: Due to the medium-high carbon content it can be welded with some precautions. Hardenability: It has a low hardenability in water or oil; fit for surface hardening that gives this steel grade a high hardness of the hardened shell.

  13. C45/1045 Steel Round Bars, C45 Steel Rods, Flat Bars, Plates

    C45/1045 carbon steel bars supplied by Metline Industries are certified to highest level of industry standards, and are accompanied by Mill Test Certificates, as per EN 10204 3.1. We can supply cut to size C45 /1045 carbon steel bars, with both small and wide diameters.

  14. China 45 Steel Equivalent, Mechanical Properties ...

    40Cr steel and other alloy steels are suitable for shaft parts with medium precision and high speed. These steels have good comprehensive mechanical properties after quenching and quenching. Equivalent Grade. 45# steel equivalent to US AISI SAE ASTM, European EN (Germany DIN EN, UK BS EN, France NF EN), Japanese JIS, and ISO standard.

  15. Steel Grade Equivalent Table (EN, SAE/AISI, UNS, DIN, BS ...

    Steel Grade Equivalent Table (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares common grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry.

  16. Material S355 Steel Properties, Comparison, Equivalent ...

    Steel Grade S355 Meaning (Designation) The following letters and numbers explains the steel grade S355 meaning. S is short for structural steel 355 refers to the minumum yield strength value for the flat and long steel thickness 16mm. JR means the impact energy value is minumum 27 J at room temperature (20).

  17. BEBON steel - C45K steel plate

    C45K steel plate, UNE36011 C45K steel plate, under UNE36011 standard, we can regard C45K steel plate as high carbon steel.. C45K steel plate is one mainly of high carbon steel,UNE36011 C45K steel plate is under EN 10250-2:1999 standard,the material Number of C45K steel plate is 1.0503 and the comparison steel grades of C45K steel is JIS G 4051 S45C,DIN17200 C45,BS970 070M46,EN10083 C45

  18. Table of Steel Equivalent Grades (EN, SAE/AISI, UNS, DIN ...

    Jul 24, 2010 · Table of Steel Equivalent Grades (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares steel equivalent grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry.

  19. SAE-AISI 1045 (S45C, G10450) Carbon Steel :: MakeItFrom.com

    SAE-AISI 1045 steel is a carbon (non-alloy) steel formulated for primary forming into wrought products. 1045 is the designation in both the SAE and AISI systems for this material. G10450 is the UNS number. It can have a moderately high tensile strength among the

  20. C45 Steel Plate, Murray Steel Products

    Description. C45 grade steel is a medium carbon steel offering moderate tensile strengths. The material is capable of through hardening by quenching and tempering on limited sections but can also be flame or induction hardened to Hrc 55.

  21. C45 Steel Plate, Murray Steel Products

    Description. C45 grade steel is a medium carbon steel offering moderate tensile strengths. The material is capable of through hardening by quenching and tempering on limited sections but can also be flame or induction hardened to Hrc 55.

  22. C45E steel - Steel grades

    Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. C45E can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join Supplier: [email protected]

  23. C45

    C45 is a medium carbon steel for e.g. mechanical engineering and automotive components. Variant SB8673 / SB-C45 is a variant with a narrowed chemical composition in order to reach a high hardenability and it is fine grain treated with Al. Variant SB1672 is a standard variant of C45

  24. C45/C45E/C45R/DIN 1.1191 - Xingsheng Special steel

    C45 steel is an unalloyed medium carbon engineering steel which has 0.42%-0.5% Carbon.It offers moderate tensile strengths,wear resistance and good machinability.this material is capable of through hardening by quenching and tempering on limited sections,and also can be flame or induction hardened to surface hardness Min 55HRC.C45 is generally supplied in an untreated or normalised condition c45 steel steel

  25. Carbon Steel C45 Sheet Plate, SAE-AISI 1045 Mild Steel ...

    A globally acclaimed industry Nextgen steel & alloys are fully involved in providing the vast array of Carbon Steel C45 / 1045 Sheet Plate.The industry is dealing as a producer, supplier and stockiest are specialized in offering such products.

  26. BEBON steel - C45K steel plate

    C45K steel plate, UNE36011 C45K steel plate, under UNE36011 standard, we can regard C45K steel plate as high carbon steel.. C45K steel plate is one mainly of high carbon steel,UNE36011 C45K steel plate is under EN 10250-2:1999 standard,the material Number of C45K steel plate is 1.0503 and the comparison steel grades of C45K steel is JIS G 4051 S45C,DIN17200 C45,BS970 070M46,EN10083 C45

  27. CK45 Carbon Steel Round Bar, S45C Round Bar, ssroundbar

    Being one of the noted manufacturer, stockists and suppliers, weoffer CK45 Carbon Steel Round Bar.Available at economical rates, the offered CK45 Carbon Steel Round Bar are widely used in metallurgical, mechanical, electrical construction field, ships, military uses and automobile rear of products.We are a prominent name in manufacturing and supplying a wide range of CK45 Carbon Steel

  28. Table of Steel Equivalent Grades (EN, SAE/AISI, UNS, DIN ...

    Jul 24, 2010 · Table of Steel Equivalent Grades (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares steel equivalent grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry.

  29. SAE-AISI 1045 (S45C, G10450) Carbon Steel :: MakeItFrom.com

    SAE-AISI 1045 steel is a carbon (non-alloy) steel formulated for primary forming into wrought products. 1045 is the designation in both the SAE and AISI systems for this material. G10450 is the UNS number. It can have a moderately high tensile strength among the

  30. Steel grades - Wikipedia

    Steel grades to classify various steels by their composition and physical properties have been developed by a number of standards organizations.. For alloys in general (including steel), unified numbering system (UNS) of ASTM International and the Society of Automotive Engineers (SAE). American steel grades : AISI/SAE steel grades standard British Standards

  31. S45C Steel For Machine Structural Use JIS G4051 - Special ...

    S45C steel grade is a very common engineering steel materials. In this post, you can check the thorough technical and properties of machine structural S45C carbon steel. 1. S45C Steels belongs to JIS G4051. S45C Steel Grade is one steel grade material in JIS G4051. which is standard specification of carbon steels for machine structural use. Specifically, this is standard for heat treatable c45 steel steel

  32. C45 Plastic Mould Steel - jaiganeshsteel.com

    c45 plastic mould steel,c45 carbon steel,c45 steel plate,c45 steel,c45 steel properties,tool steel grades,c45 steel hardness,alloy steel grades,plastic steel. WHAT IS C45 PLASTIC MOULD STEEL PLATE? In fact, C45 Plastic Mould Steel Plate is the Best Product. And also, The Quality Product by Jai Ganesh Steel. Not only this but also the Unique c45 steel steel

  33. C45 Carbon Steel Round Bar, S45C Round Bar, ssroundbar

    Being one of the noted manufacturer, stockists and suppliers, weoffer C45 Carbon Steel Round Bar.Available at economical rates, the offered C45 Carbon Steel Round Bar are widely used in metallurgical, mechanical, electrical construction field, ships, military uses and automobile rear of products.We are a prominent name in manufacturing and supplying a wide range of C45 Carbon Steel

  34. Alloy Steel Round Bars, Grades AISI 1045 (DIN-1.1730) (IS ...

    Guru Gautam Steels are Manufacturers, Supplier and Exporters of High quality AISI 1045 (DIN-1.1730) (IS-C45) in Mumbai India. These AISI 1045 Steel is also a quenching and tempering steelSome results are removed in response to a notice of local law requirement. For more information, please see here.

Online Consultation