aisi d2 tool steel columbium alloy sheet Related introduction

  1. D2 Tool Steel, 1.2379, SKD11 Tool Steel - Otai Special Steel

  2. AISI D2, Cold Work Tool Steel, Data Sheet

    AISI D2 is recommended for tools requiring very high wear resistance, combined with moderate toughness (shock-resistance). AISI D2 can be supplied in various finishes, includ-ing the hot-rolled, pre-machined and fine machined condition. AISI D2 is a high-carbon, high-chromium tool steel alloyed with molybdenum and vanadium charac-terized by:

  3. HCHCR D2 / AISI D2 / DIN 1.2379 Tool Steel, Ventura Steels

  4. Alloys & Tool Steel - alro.com

    Alloys and Tool Steel Bar and Plate Products aisi d2 tool steel columbium alloy sheet Alloys and Tool Steel AISI 4140 - Annealed Flats and Squares HR (Cut From Plate) (Also available in DCF) Please refer to pages 8-32 thru 8-33 for alloy tolerances. Note, sizes not listed above can be cut from plate.

  5. ASTM A681, for Tool Steels Alloy - Otai Special Steel

    ASTM A681 specification covers the chemical, mechanical, and physical requirements for available wrought alloy tool steel products, which include hot or cold finished steel bar, steel plate, steel sheet, strip, rod, wire, or forgings etc.. Material in accordance with ASTM A681 specification is classified by chemical composition. There are Hot Work Tool Steel, Cold Work Tool Steel, Shock aisi d2 tool steel columbium alloy sheetSome results are removed in response to a notice of local law requirement. For more information, please see here.

  6. AISI D2, AISI D2 Tool Steel, AISI D2 Cold Work Tool Steel

    Virat Special Steels is the biggest & leading Supplier & Stockiest of AISI D2 Steel. AISI D2 Consolidates maximum wear resistance, great durability, exceptional front line maintenance and treating resistance. 12 % ledeburitic chromium steel. It can be nitride after special heat treatment.

  7. D2 Tool Steel, 1.2379, Cr12MoV, SKD11 steel - Special ...

    D2 Tool Steel, 1.2379, Cr12MoV, SKD11 steel. What is D2 tool steel AISI D2 is a cold work tool steel. Cold work dies steel D2 tool steel with high abrasion resistance, micro-deformation, the wind hard tool steel, carbon content as high as 1.5%, chromium content as high as 11.5%, the heat treatment hardness can reach 60 HRC.

  8. SAE-AISI D2 (T30402) Chromium Cold-Work Steel ...

    SAE-AISI D2 steel is a tool steel. D2 is the designation in both the SAE and AISI systems for this material. T30402 is the UNS number. It can have the highest ductility among the tool steels in the database. The properties of SAE-AISI D2 steel include two common variations. This page shows summary ranges across both of them.

  9. D2 Tool Steel, 1.2379 - Dongguan OTAI Special Steel Co

    D2 Tool steel is a ASTM cold work steel. it is equivalent with GB Cr12Mo1V1, Jis SKD11, DIN 1.2379 steel. aisi d2 tool steel columbium alloy sheet Supply Form of D2 Steel -ASTM A681 Alloy Cold Work Tool Steel . Square Round Plate sheet Supply Range of aisi D2 Steel aisi d2 tool steel columbium alloy sheet ASTM AISI D2 Tool Steel Material Mechanical Properties. Hardness, Rockwell C: 69 HRc. Izod impact unnotched: 77 J

  10. HCHCR D2 / AISI D2 / DIN 1.2379 Tool Steel, Ventura Steels

    Ventura Alloy and Steels Supplies and Stocks HCHCR D2 steel in India and abroad. D2 steel is an air hardening, high-carbon, high-chromium tool steel. It has high wear and abrasion resistant properties. It is heat treatable and will offer a hardness in the range 55-62

  11. eFunda: Properties of Tool Steel AISI D2

    Materials » Alloys » Steel » Tool Steel » AISI T8 Materials » Alloys » Steel » Alloy Steel » AISI 1345 Beams » Simply Supported » Uniformly Distributed Load » Four Equal Spans » S Section Steel

  12. Tool Steel D2, All Metals & Forge Group

    Tool Steel D2 Principal Design Features. This alloy is one of the Cold Work, high carbon, high chromium type tool steels. D2 is a deep hardening, highly wear resistant alloy. It hardens upon air cooling so as to have minimum distortion after heat treatment. Applications

  13. MetalsDepot® - D2 Flat Ground Tool Steel

    D2 Flat Ground, is an air-hardening, high carbon , high chromium tool steel with extremely high wear resisting properties. It is a very deep hardening steel and will be practically free from size change after proper treatment. The high percentage of chromium gives it mild corrosion resisting properties in the harden condition.

  14. D2 Tool Steel - West Yorkshire Steel - Special Steel

    D2 tool steel stockholders and suppliers, delivering to the whole of the UK. West Yorkshire Steel are suppliers of D2 tool steel in round bar, plate, sheet and block which can be bandsaw cut to your requirements. A high carbon high chromium tool steel grade offering very

  15. D2 Alloy Steel Sheet, D2 Alloy Steel Sheet Suppliers and ...

    Alibaba.com offers 532 d2 alloy steel sheet products. About 11% of these are steel sheets, 1% are stainless steel sheets, and 1% are other stainless steel. A wide variety of d2 alloy steel sheet options are available to you, such as aisi, jis, and gb.

  16. S7, D2, A2: Difference in tool steel properties, Paulo

    Over the years, metallurgists have tweaked alloy steel formulas to meet specific needs or working conditions. As a result, dozens of tool steel types exist. The specific properties of S7, D2 and A2 tool steels, which are among the most popular in industrial and manufacturing applications today, are discussed in further detail below.

  17. Tool steel - Wikipedia

    Tool steel refers to a variety of carbon and alloy steels that are particularly well-suited to be made into tools.Their suitability comes from their distinctive hardness, resistance to abrasion and deformation, and their ability to hold a cutting edge at elevated temperatures. As a result, tool steels are suited for use in the shaping of other materials.

  18. Tool Steel, Samuel, Son & Co.

    Making tools requires a special kind of steel, and Samuel is here to make sure you can find exactly what youre looking for. We look at the distinctive hardness, resistance to abrasion and deformation required of the carbon and alloy steels destined for tool making and we stock one of the most extensive inventories of tool steels in round bar, flat bar and plate.

  19. D-2 Air Hardening Tool Steel - Specialty Metal Distributors

    D-2 tool steel is a versatile high-carbon, high-chromium, air-hardening tool steel that is characterized by a relatively high attainable hardness and numerous, large, chromium rich alloy

  20. AISI D2, AISI D2 Tool Steel, AISI D2 Cold Work Tool Steel

  21. D2 Tool Steel - West Yorkshire Steel

    D2 Tool Steel D2 tool steel stockholders and suppliers, delivering to the whole of the UK. West Yorkshire Steel are suppliers of D2 tool steel in round bar, plate, sheet and block which can be bandsaw cut to your requirements.

Online Consultation